Fast Order: Most Common Items

Pressed Steel Putlog Single Couplers connect scaffolding putlogs or transom scaffold tubes to ledger scaffold tubes for the support of scaffolding boards.

It should not be used as a load bearing scaffolding coupler. 

BS1139 Standard.

Colour / Finish may vary.

Double Couplers are used to connect ledgers to standards at 90 degrees.

EN74-1A / B Standard.

Colour / Finish may vary.

Double Couplers are used to connect ledgers to standards at 90 degrees.

EN74 Class B / 1B Standard.

Colour / Finish may vary.

Swivel Couplers enable two scaffold tubes to be connected together at any angle, they are used mainly for diagonal bracing.

EN74-1 Class A Standard.

Colour / Finish may vary.

Swivel Couplers enable two scaffold tubes to be connected together at any angle, they are used mainly for diagonal bracing.

EN74-1 Class A Standard.

Colour / Finish may vary.

External Coupler for end to end joints on either standards, ledgers or bracing.

EN74 Class B / 1B Standard.

Colour / Finish may vary.

Internal coupler for end to end joining of tubes, must only be used vertically and therefore sleeve couplers are now more commonly used for all joints.

Colour / Finish may vary.

Used to provide a flat bearing surface for even load distribution of scaffold standards, should be used in conjunction with sole pads.

Colour / Finish may vary.

NOT Galvanised / plated

For use with standard tubes to convert them to putlogs.

Colour / Finish may vary.

Gravlock type girder clamps enable scaffold tubes to be secured to / against “I” beam girders.

Gravlocks should always be used in pairs.

AS-1576 Standard

Colour / Finish may vary.

Used to hold down scaffold boards in exposed areas.

The advantages of using a Limpet Clip over standard board retaining clips are as follows:

• No trip hazard - domed finish.
• Fastened from above.
• No projecting bolts on underside.
  
• Can also be used on battens: 63mm thickness

Swivel Girder Clamps enable scaffold tubes to be secured to / against “I” beam girders.

Girder Clamps should always be used in pairs.

Fixed Type also available.

AS 1576 Standard.

Colour / Finish may vary.

Where secure connection of boards to scaffold is required.

Colour / Finish may vary.

Scaffold Boards to BS 2482. UK manufactured Kite Marked Boards, not cheaper imports. ( all timber is European Whitewood )

10ft / 3.0m length, 38mm thickness x 225mm width, fitted with end hoop irons for protection.

Available in the following lengths

• 13ft / 3.9m
  
• 10ft / 3.0m
  
•   8ft / 2.4m
  
•   6ft / 1.8m
  
•   5ft / 1.5m
  

Flame proof scaffold boards are also available on request.

If using Scaffold Boards for furniture etc... please contact the office on 01469 572321 prior to ordering.

Please be aware that scaffold boards are predominantly used outdoors, if used inside or in dry / hot weather conditions they will be subject to splitting etc, if using these for inside project / furniture etc they should be dry stored first to eliminate any cracking / splitting.

Scaffold Boards to BS 2482. UK manufactured Kite Marked Boards, not cheaper imports. ( all timber is European Whitewood )

10ft / 3.0m length, 38mm thickness x 225mm width, fitted with end hoop irons for protection.

Available in the following lengths

• 13ft / 3.9m
  
• 10ft / 3.0m
  
•   8ft / 2.4m
  
•   6ft / 1.8m
  
•   5ft / 1.5m
  

Flame proof scaffold boards are also available on request.

If using Scaffold Boards for furniture etc... please contact the office on 01469 572321 prior to ordering.

Please be aware that scaffold boards are predominantly used outdoors, if used inside or in dry / hot weather conditions they will be subject to splitting etc, if using these for inside project / furniture etc they should be dry stored first to eliminate any cracking / splitting.

Scaffold Boards to BS 2482. UK manufactured Kite Marked Boards, not cheaper imports. ( all timber is European Whitewood )

8ft / 2.4m length, 38mm thickness x 225mm width, fitted with end hoop irons for protection.

Available in the following lengths

• 13ft / 3.9m
  
• 10ft / 3.0m
  
•   8ft / 2.4m
  
•   6ft / 1.8m
  
•   5ft / 1.5m
  

Flame proof scaffold boards are also available on request.

If using Scaffold Boards for furniture etc... please contact the office on 01469 572321 prior to ordering.

Please be aware that scaffold boards are predominantly used outdoors, if used inside or in dry / hot weather conditions they will be subject to splitting etc, if using these for inside project / furniture etc they should be dry stored first to eliminate any cracking / splitting.

Scaffold Boards to BS 2482. UK manufactured Kite Marked Boards, not cheaper imports. ( all timber is European Whitewood )

6ft / 1.8m length, 38mm thickness x 225mm width, fitted with end hoop irons for protection.

Available in the following lengths

• 13ft / 3.9m
  
• 10ft / 3.0m
  
•   8ft / 2.4m
  
•   6ft / 1.8m
  
•   5ft / 1.5m
  

Flame proof scaffold boards are also available on request.

If using Scaffold Boards for furniture etc... please contact the office on 01469 572321 prior to ordering.

Please be aware that scaffold boards are predominantly used outdoors, if used inside or in dry / hot weather conditions they will be subject to splitting etc, if using these for inside project / furniture etc they should be dry stored first to eliminate any cracking / splitting.

Scaffold Boards to BS 2482. UK manufactured Kite Marked Boards, not cheaper imports. ( all timber is European Whitewood )

5ft / 1.5m length, 38mm thickness x 225mm width, fitted with end hoop irons for protection.

Available in the following lengths

• 13ft / 3.9m
  
• 10ft / 3.0m
  
•   8ft / 2.4m
  
•   6ft / 1.8m
  
•   5ft / 1.5m
  

Flame proof scaffold boards are also available on request.

If using Scaffold Boards for furniture etc... please contact the office on 01469 572321 prior to ordering.

Please be aware that scaffold boards are predominantly used outdoors, if used inside or in dry / hot weather conditions they will be subject to splitting etc, if using these for inside project / furniture etc they should be dry stored first to eliminate any cracking / splitting.

Aluminium Scaffold Tube

20ft / 6.0m - Length sizes are approx - Please contact our office if specific cuts are required

48.3mm x 4.05mm wall thickness 

Manufactured in accordance to BS1139

Graded to EN755/573

Available in various lengths.

Aluminium Scaffold Tube

10ft / 3.0m - Length sizes are approx - Please contact our office if specific cuts are required.

48.3mm x 4.05mm wall thickness.

Manufactured in accordance to BS1139

Graded to EN755/573

Available in various lengths.

Aluminium Scaffold Tube

1.5m / 5ft - Length sizes are approx - Please contact our office if specific cuts are required.

48.3mm x 4.05mm wall thicknes.

Manufactured in accordance to BS1139

Graded to EN755/573

Available in various lengths.

H.T. Galvanised Scaffold Tube

H.T. Galvanised Scaffold Tube

H.T. Galvanised Scaffold Tube

H.T. Galvanised Scaffold Tube

H.T. Galvanised Scaffold Tube

After recognised construction industry feedback, we are now delighted to offer the LH / RH closing gate.

• Double Handrail Depth
• Steel Toe Board
• Fully Meshed
• System Compatible, with additional components.
• Gate Size: 600 x 960mm - size may vary.
• Distance between standards: 780mm Approx
• Please have gate available on site before erecting standards/posts
• Presco type half coupler fastening
• Weight: 12 Kgs

Used as a safety trap door, a ladder access transom is used on the scaffold to form a " hole / opening " that a worker can climb through. The safety trapdoor is held in place by adjustable clamps held against the toeboards.

• Fits on Kwikstage
• Fits on Scaflok / Cuplok
• A ladder access transom will also be required.
• Fitting details available on the download
  
• Colour may vary
• Mesh size: 58 x 71cm (may vary)
  

Design may vary.

Galvanised Scaffold Tube

Galvanised Scaffold Tube

Galvanised Scaffold Tube

13ft / 3.9m in length.

48.3 x 4.0mm wall thickness.

Graded to EN39.

Other lengths also available.

Galvanised Scaffold Tube

Galvanised Scaffold Tube

Galvanised Scaffold Tube

Galvanised Scaffold Tube

Internal coupler for end to end joining of tubes, must only be used vertically and therefore sleeve couplers are now more commonly used for all joints.

Colour / Finish may vary.

Where secure connection of toe boards to standards is required.

Colour / Finish may vary.

Used in pairs when a temporary stair tread is required, fully adjustable to any angle / rake and are left or right handed.

Complete stair tread units are also available.

Band & Plate coupler is used to connect two scaffold tubes at a right angle.

This two part coupler has two 18mm bolt holes to allow the coupler to be fixed to a wall or ceiling etc.

Zinc plated.

Colour / Finish may vary.

Components also sold seperately (Product Codes: 20805 & 40805)

Drop Forged Half Coupler.

18mm Hole size approx.

Can be welded into place.

Colour / Finish may vary.

Roofing Coupler used to hold Galv Corrugated Sheets in place.

Easy to use.

No drilling required.

May be Drop Forged or Pressed Steel depending on stocks

Roofing Coupler Fixing Sheet available to download.

Colour / Finish may vary.

"The Jordan Safety Clamp" is a unique product devised to meet the need to eliminate the dangers faced by the scaffold operatives whilst working at height.

The Jordan Safety Clamp is a simple cost effective product that will save lives. Falls account for nearly two thirds of all fatal accidents in the construction industry. According to Health, Safety and Welfare Regulations 1996 operatives must be provided with SUITABLE means of protection to prevent a fall.

The primary safety objective is to provide physical safeguards to prevent falls during the erection, modification and dismantling of scaffolding installations. There is no equipment currently available to secure a man above head height at all times – The Jordan Clamp eliminates this problem.

The Jordan Safety Clamp, as inspected by the HSE, is a simple cost-effective safety device that enables the scaffolder to hook up to a failsafe security point as soon as he leaves ground level (or after all levels above the first lift). The scaffolder is secure at all times but has freedom of movement and can add or remove scaffolding components without unclipping his safety lanyard.

Before the introduction of The Jordan Safety Clamp scaffolders did not have a secure point of anchor when erecting dismantling or modifying scaffolding structures, these dangers are completely eliminated providing the scaffolder uses Jordan Safety Clamps.

The Jordan Safety Clamp is already secured to the standard as scaffold building begins from ground level, providing a safe anchor point above head height at all times. It allows instant access and continuous protection during all work and scaffolding operations and does not impede or slow down operations.

Swivel Base Screw Jacks locate in the bottom of the standards, they provide adjustment to cope with variations in ground levels, and they have the ability to swivel to cope with slopes etc.

Safe working load of approx 6 tons.

Overall Height approx 650mm, Adjustable Range approx 500mm

Approx 38mm OD.

Plate approx 150 x 150 x 6mm.

Used to secure and safely fix a steel section ladder to a scaffold tube, use in pairs.

Double Sided for most section types.

Throat size: Approx 25mm width.

Colour / Finish may vary.

Oyster Couplers connect putlogs or transom tubes to ledger tubes for the support of scaffold boards.

Oyster Couplers should not be used as a load bearing coupler.

BS1139 Standard.

Colour / Finish may vary.

Will secure timber joists to scaffold tube.

Fitting will take a timber 60mm width max.

Colour / Finish may vary.

 Was £2.65, Now Only £1.75 Each

Used to  secure hoarding / fence panels  to scaffold tube.

Will take a 45mm wide timber (max 47mm gap)

Colour / Finish may vary.

We also have available a joist coupler for use on timber joists / hoardings please

see Item No: 10907

For use with Base Plates or Base Jacks on soft ground conditions.

Approx 18" length.

Metal end plate for use on standard scaffold boards.

Colour / finish may vary.

Galvanised Scaffold Tube

Galvanised Scaffold Tube

Galvanised Scaffold Tube

Galvanised Scaffold Tube

Fully Galvanised Steel Ladder Beams.

21ft / 6.3m length, approx 353mm width.

.BS EN 1993:1  BS EN 12811

Aluminium 450mm Beams, Fully compatible with Layher Beams.

Full spec sheet available on request.

Beams can be joined together to form longer runs, see technical data for more info.

Manufactured in accordance with BS EN1999-1-1

Available in various lengths.

Joints for use with Aluminium Beams.

Fully compatible with Layher Beams.

Use in pairs.

Priced each c/w four spring pins

Full spec sheet available on request.

Beams can be joined together to form longer runs.

Tube Castor for fitting onto standard scaffold tube and/or Kwikstage, this type of castor will not fit Cuplok system scaffolding.

• Braked
• Rubber Tyre
• 8" - 200mm
• SWL - 535kg

Plastic Tube End Cap to fit over standard size scaffold tube.

• Bright Easy To See Colour
• Cheap Yet Robust
• Safely Protects Tube Ends
• Also Available Fitting Bolt caps

Plastic Tube End Cap to fit over standard size scaffold tube.

• Bright Easy To See Colour
• Cheap Yet Robust
• Safely Protects Tube Ends
• Also Available Fitting Bolt caps

Plastic Tube End Cap to fit over standard size scaffold tube.

• Bright Easy To See Colour
• Cheap Yet Robust
• Safely Protects Tube Ends
• Also Available Fitting Bolt caps

Plastic Tube End Cap to fit over standard size scaffold tube.

• Bright Easy To See Colour
• Cheap Yet Robust
• Safely Protects Tube Ends
• Also Available Fitting Bolt caps

Plastic Cap to fit over bolt ends on standard scaffold fittings.

• Easy to fit
• Bright Colours
• Protects against catching clothes

Plastic Cap to fit over bolt ends on standard scaffold fittings.

• Easy to fit
• Bright Colours
• Protects against catching clothes

Plastic Cap to fit over bolt ends on standard scaffold fittings.

• Easy to fit
• Bright Colours
• Protects against catching clothes

Plastic Cap to fit over bolt ends on standard scaffold fittings.

• Easy to fit
• Bright Colours
• Protects against catching clothes

Plastic Fitting Protector - to fit over standard size scaffold fitting.

• Bright Easy To See Colour
• Cheap Yet Robust
• Safely Protects From Rips / Tears
• Also Available Tube End Caps & Fitting Bolt caps

Hilti type ring used to "tie" scaffolds to buildings

• Galvanised
• Anchor is required for fixing
• SDS Drill bit available

Gravlok type anchor system

Please download pdf file for full info

Only to be used on good brick / solid walls / floors.

M16 Fitting

Gravlok type anchor system

Please download pdf file for full info

Only to be used on good brick / solid walls / floors.

M16 Fitting

Anchors for use with Hilti Rings.

Only to be used on good brick / solid walls / floors.

M16 Fitting

For Use With Hilti Anchor

Fittings bags with 30kg S.W.L. printed on. 

Ideal for use on site where Health and Safety requires lifting bags to be  stamped with S.W.L.

Holds approx 20 / 25 fittings - 30kg max 

We have these manufactured and tested in the UK.

You can download the batch test certificate, they failed at 1200kgs, thats a safety factor of 40:1, most other bags are only 6:1

Scaffold Stillage to hold either standard scaffolding and/or Kwikstage or Cuplok items.

Designed to stack together, will fit on top of fitting bins.

• Standard Size
• Fits on/under Fitting Bins
• Robust Construction
• Square Leg
• SWL 1.4 tons
• Can stack 6 high

CONDITION MAY VARY

Safety Light for Tube / Kwikstage / Cuplok / Layher etc

Photo electric cell for nightime operation

Includes fixing tool and Batteries

Scafftag Safety System, used worldwide as an inspection/fit for use type safety system.

Each kit contains:

• 10 Holders
• 20 Inserts
•   1 Pen

Laddertag Safety System, used worldwide as an inspection / fit for use type safety system.

Each kit contains:

• 10 Holders
• 10 Inserts
• 1 Pen

Ginn Wheel used to hoist materials up onto scaffold.

Manufactured in accordance with BS1692.

Test certificate supplied with each Ginn Wheel.

Rope sold seperately.

Used to secure and safely fix a ladder to a scaffold.

To be used in pairs.

3.0mm diameter wire c/w sealed ends.

Used to form temporary staircase, fully adjustable to any angle / rake and are left or right handed.

• Tread Size 900 mm x 230 x 45mm
• 2 nos 100mm fixing tubes at each end
• Can be fitted with double couplers
• Colour / Finish may vary.

Hook Type anchor system

Only to be used on good brick / solid walls / floors.

• Half Coupler c/w Hook End
  
• Ring Screw NOT included, see below
  

Friction Clamps are used where a scaffold needs to be erected from a round pipe,  they are used in off shore applications

Please note that the price does NOT include the cost of H.T. Chain or fitting/testing

H.T. Chain is £ 12.00 / mtr

Fitting / Testing is £ 20.00 ea

For further info please contact the office by email,  let us know the diametre of pipe that they are to be used on.

Screw Jacks locate in the bottom of the standards, they provide adjustment for variations in ground levels.

Safe working load of approx 4 tons each.

Overall Height approx 650mm, Adjustable Range approx 500mm

Approx 38mm OD.

Plate approx 150 x 150 x 5mm.

Screw Jacks locate in the bottom of the standards, they provide adjustment for variations in ground levels.

Safe working load of approx 6 tons each.

Overall Height approx 650mm, Adjustable Range approx 500mm

Approx 38mm OD

Plate approx 150 x 150 x 6mm.

Lightweight steel frame for displaying customers own sign boards.

Signboard not included.

Lightweight steel frame for displaying customers own sign boards.

Signboard not included.

Single Tube Type anchor system

Can to be used on good brick / solid walls / floors, and also timber frames ( subject to suitability )

• Standard tube size for easy use with most scaffold fittings
  
• Can be fixed with M12 Excalibur 20mm Hex Head Bolts
• Standard wood screws and washers can be used on timber frames
• Tested to 20KN force
• Twin Tube version also available
• Approx Tube Length: 300mm

Please Note: All fixings MUST be checked for " pull " strength.     

Rawplugs are not required with Excalibur fixings

Double Tube Type anchor system

Can to be used on good brick / solid walls / floors, and also timber frames ( subject to suitability )

• Standard tube size for easy use with most scaffold fittings
  
• Can be fixed with Excalibur 20mm Hex Head Bolts
• Standard wood screws and washers can be used on timber frames
• Tested to 20KN force
• Single Tube version also available
• Approx Tube Length: 300mm each
  

Please Note: All fixings MUST be checked for " pull " strength.     

Rawplugs are not required with Excalibur fixings

For use with Single and Double Tube Type anchor system

Can to be used on good brick / solid walls / floors, and also timber frames (subject to suitability)

• Thunderbolt 19mm Hex Head Bolts - sold seperately
  
• M12 x 100mm
• M12 / 12mm drill bit required
• Sizes on download

Please Note: All fixings MUST be checked for " pull " strength.     

Rawlplugs are not required with Thunderbolt fixings

Scaffold Tube Sleeving

500m Roll

Easily slips over tubes

Other colours available:

Black/Yellow

Scaffold Tube Sleeving

500m Roll

Easily slips over tubes

Other colours available:

Red / White

Pressed Steel Half Coupler.

16mm Hole size approx.

Can be welded into place.

Colour / Finish may vary.

Foam Tube Sleeve to fit over standard size scaffold tube. Colour may vary

• Bright Easy To See Colour
• Cheap Yet Robust
• Approx 75mm Outside Diametre
• High Density Quality
• Safely Protects the Public / Tube
• 10 pcs x 2.0m Lengths

Foam Tube Sleeve to fit over standard size scaffold tube. Colour may vary

• Bright Easy To See Colour
• Cheap Yet Robust
• Approx 75mm Outside Diametre
• High Density Quality
• Safely Protects the Public / Tube
• 10 pcs x 2.0m Lengths

Foam Tube Sleeve to fit over standard size scaffold tube. Colour may vary

• Bright Easy To See Colour
• Cheap Yet Robust
• Approx 75mm Outside Diametre
• High Density Quality
• Safely Protects the Public / Tube
• 10 pcs x 2.0m Lengths

Scaffold Stillage to hold either standard scaffolding and/or Kwikstage or Cuplok items.

Designed to stack together, will fit on top of fitting bins.

• Standard Size
• Fits on/under Fitting Bins
• Robust Construction

Aluminium 450mm Beams, Fully compatible with Layher Beams.

Full spec sheet available on request.

Beams can be joined together to form longer runs, see technical data for more info.

Manufactured in accordance with BS EN1999-1-1

Available in various lengths.

Aluminium 450mm Beams, Fully compatible with Layher Beams.

Full spec sheet available on request.

Beams can be joined together to form longer runs, see technical data for more info.

Manufactured in accordance with BS EN1999-1-1

Available in various lengths.

Aluminium 450mm Beams, Fully compatible with Layher Beams.

Full spec sheet available on request.

Beams can be joined together to form longer runs, see technical data for more info.

Manufactured in accordance with BS EN1999-1-1

Available in various lengths.

Spring Pins for use with Aluminium Beam Joints.

Fully compatible with Layher Beams.

Supplied individually - you will require four pins per spigot, two spigots per joint, ie two joints and eight pins

( These clips can also be used to join kwikstage standards but NOT cuplok )

Heavy Duty Base Plate

Zinc Plated 150 x 150 x 4.0mm c/w locating spigot ( approx 30mm OD x 50mm )

Used to provide a flat bearing surface for even load distribution of scaffold standards, should be used in conjunction with sole pads.

Manufactured in accordance to EN74.

Colour / Finish : Self Colour

Used to secure and safely fix a timber pole ladder to a scaffold, use in pairs.

This Ladder Clamp should also be used to hold single section ladders against Kwikstage transom units.

Colour / Finish may vary.

Sisal Rope used to hoist materials up onto scaffold.

Ginn Wheel supplied seperately.

Rope Size: 20m length x 24mm dia

Used to Safely Lift Galvanised Corrugated Sheets

• 6 x 10ft long Sheets per lift ( 66kg max )
  

• ScaffCorroClamp

• Easy to use
  

• No Drilling Required
  
  
• Test Cert with each clamp.
  

Galvanised Corrugated Sheets

• 3.0m / 10ft long 10/3" corrugation

• 762mm cover width (Overall approx 820mm width)

• 24 swg (0.55mm)
  
  
• Easy to use 
  
  
• No Drilling Required
  
  
• Roofing Coupler Fixing Sheet available to download

You can download the data sheet and how to fix leaflet from the Download Tab above

Roofing Couplers are used to hold Galv Corrugated Sheets in place without having to drill etc.

SCAFFEZE quickly penetrates and removes rust, corrosion, grease and other contamination from all fittings and screw threads. SCAFFEZE not only frees all seized parts but also lubricates and leaves them in first class working order.

• Eco friendly
• Safe and reliable to use
  

Joints for use with Aluminum Beams.

Fully compatible with Layher Beams.

Use in pairs.

Priced indivually.

Please Note: Minimum Qty is 100 nos

BS 2482 Fireproof Scaffold Boards are ideal for use in stage and theatre applications.

UK manufactured Kite Marked Boards, not cheaper imports. ( all timber is European Whitewood )

13ft / 3.9m length, 38mm thickness x 225mm width, fitted with end hoop irons for protection.

Available in various lengths (upon request)

If using Scaffold Boards for furniture etc... please contact the office on 01469 572321 prior to ordering.

Please be aware that scaffold boards are predominantly used outdoors, if used inside or in dry / hot weather conditions they will be subject to splitting etc, if using these for inside project / furniture etc they should be dry stored first to eliminate any cracking / splitting.

Folds flat for easy transportation

Height adjustable to suit tube & fitting and system scaffolding (3 x height adjustments)

Weighs only 7.4kg

Locks onto scaffold tube

Meets requirements of NASC code of practice

Aluminum anti-slip work platform

Scaffold Stillage to hold either standard scaffolding and/or Kwikstage or Cuplok items.

Designed to stack together, will fit on top of fitting bins.

• Standard Size
• Fits on/under Fitting Bins
• Robust Construction
• Square Leg
• SWL 1.4 tons
• Can stack 6 high

Painted Black

LED Light for Tube / Kwikstage / Cuplok / Layher etc

Approx 12 month battery life.

After recognised construction industry feedback, we are now delighted to offer the LH / RH side panel to enable a standard self closing gate to be used on the end of a Cuplok bay ie 1.3m width.. or a kwikstage bay ie 4'2 width.

• Double Handrail Depth
• Painted Finish
• Can be used RH or LH Side
• Steel Toe Board
• Fully Meshed
• Works with standard and omega cuplok system
• Works with kwikstage
• System Compatible, with additional components.
• Used with Gate Size: 750 x 960mm( not included )
  
• Weight: 10 Kgs

Used to provide a mesh barrier along between the scaffold handrail and toe board. Plastic Brick Guards prevent debris etc from falling off a scaffold, they are approx 1.0m in length.

• Size: 110 width x 84cm high
• No hooks to attach count or lose!
• Complete one-piece construction with no separate parts.
• No additional fixings required.
• Built in toe board clip prevents movement, even in high winds.
• No more creasing, fracturing or hooks falling off. 
• High grade impact modified polypropylene for durability and flexibility.

• Easy to stack. Easy to separate. Anti-tangle guaranteed!
• Vertical stacking design with four way stay-fast alignment.
• Great for storage, delivery and movement around site!
• Interlocking features maximise stability.
• Make every job stand out from the competition!
• Wide range of colours in stock and pantone colour matching available.
• Max Unique hook design!
• Reduces accidental displacement.

Used to provide a mesh barrier along between the scaffold handrail and toe board. Plastic Brick Guards prevent debris etc from falling off a scaffold, they are approx 1.0m in length.

• Size: 110 width x 84cm high
• No hooks to attach count or lose!
• Complete one-piece construction with no separate parts.
• No additional fixings required.
• Built in toe board clip prevents movement, even in high winds.
• No more creasing, fracturing or hooks falling off. 
• High grade impact modified polypropylene for durability and flexibility.

• Easy to stack. Easy to separate. Anti-tangle guaranteed!
• Vertical stacking design with four way stay-fast alignment.
• Great for storage, delivery and movement around site!
• Interlocking features maximise stability.
• Make every job stand out from the competition!
• Wide range of colours in stock and pantone colour matching available.
• Max Unique hook design!
• Reduces accidental displacement.

Used to provide a mesh barrier along between the scaffold handrail and toe board. Plastic Brick Guards prevent debris etc from falling off a scaffold, they are approx 1.0m in length.

• Size: 110 width x 84cm high
• No hooks to attach count or lose!
• Complete one-piece construction with no separate parts.
• No additional fixings required.
• Built in toe board clip prevents movement, even in high winds.
• No more creasing, fracturing or hooks falling off. 
• High grade impact modified polypropylene for durability and flexibility.

• Easy to stack. Easy to separate. Anti-tangle guaranteed!
• Vertical stacking design with four way stay-fast alignment.
• Great for storage, delivery and movement around site!
• Interlocking features maximise stability.
• Make every job stand out from the competition!
• Wide range of colours in stock and pantone colour matching available.
• Max Unique hook design!
• Reduces accidental displacement.

Used to provide a mesh barrier along between the scaffold handrail and toe board. Plastic Brick Guards prevent debris etc from falling off a scaffold, they are approx 1.0m in length.

• Size: 110 width x 84cm high
• No hooks to attach count or lose!
• Complete one-piece construction with no separate parts.
• No additional fixings required.
• Built in toe board clip prevents movement, even in high winds.
• No more creasing, fracturing or hooks falling off. 
• High grade impact modified polypropylene for durability and flexibility.

• Easy to stack. Easy to separate. Anti-tangle guaranteed!
• Vertical stacking design with four way stay-fast alignment.
• Great for storage, delivery and movement around site!
• Interlocking features maximise stability.
• Make every job stand out from the competition!
• Wide range of colours in stock and pantone colour matching available.
• Max Unique hook design!
• Reduces accidental displacement.

Used to provide a mesh barrier along between the scaffold handrail and toe board. Plastic Brick Guards prevent debris etc from falling off a scaffold, they are approx 1.0m in length.

• Size: 110 width x 84cm high
• No hooks to attach count or lose!
• Complete one-piece construction with no separate parts.
• No additional fixings required.
• Built in toe board clip prevents movement, even in high winds.
• No more creasing, fracturing or hooks falling off. 
• High grade impact modified polypropylene for durability and flexibility.

• Easy to stack. Easy to separate. Anti-tangle guaranteed!
• Vertical stacking design with four way stay-fast alignment.
• Great for storage, delivery and movement around site!
• Interlocking features maximise stability.
• Make every job stand out from the competition!
• Wide range of colours in stock and pantone colour matching available.
• Max Unique hook design!
• Reduces accidental displacement.

Scaffold Bin to hold scaffold fittings and/or Kwikstage or Cuplok items.

Designed to stack together, will fit on top of stillages or fitting bins.

• 940cm x 940cm. 645cm Overall Height, 380cm Internal Height
• Fits on/under Fitting Bins or Stillages
• Robust Construction
• SWL 1.0 ton
• Can stack 6 high
• Please note that these bins are once used.
  

Rope Size: 20m length x 6mm diameter

Foam Tube Sleeve to fit over standard size scaffold tube. Colour may vary

• Bright Easy To See Colour
• Approx 75mm Outside Diametre
• High Density Quality
• Cheap Yet Robust
• Safely Protects the Public / Tube
• 10 pcs x 2.0m Lengths

Pigs Tail Joint Pins for use with Kwikstage or Cuplok.

Supplied individually

These are a "loose" fit item, not to be used for suspended scaffolds.

T Bolt, 7/16" Nut & Washer Set for Scaffold Fittings.

Come in packs of 100 pieces.

Fitting T Bolt - Weight 0.074kg, Length of Thread 53.5mm,  Overall Length 85mm 

Fitting Nut- Weight 0.022kg 

Fitting Washer - Weight 0.009kg 

All dimensions/weights are approximate.

Please note, this is a standard size for scaffold fittings, some scaffold fittings may require different size bolts.

Colour / Finish may vary.

H.T. Galvanised Scaffold Tube

H.T. Galvanised Scaffold Tube

H.T. Galvanised Scaffold Tube

H.T. Galvanised Scaffold Tube

The Lay Flat Scaffold Fitting eradicates the process of lapping boards on scaffold returns, reducing tripping hazards and increasing safety.

This Lay Flat Scaffold Fitting is tested to 9.1 KN with a Class B certification complete with EN74 – 1 BM

Colour / Finish may vary.

The Saddle Scaffold Fitting is for use with conventional Tube, Boards & Fittings.

 Colour / Finish may vary.

Was £4.50, Now Only £2.95 Each

Aluminium Scaffold Tube

2.0m / 6'6"ft - Length sizes are approx - Please contact the office if specific cuts are required.

48.3mm x 4.05mm wall thickness.

Manufactured in accordance to BS1139

Graded to EN755/573

Available in various lengths.

Plastic Tube End Cap to fit over standard size scaffold tube. Colour may vary

• Cheap Yet Robust
• Safely Protects Tube Ends
• Also Available Fitting Bolt caps

Plastic Cap to fit over bolt ends on standard scaffold fittings.

• Easy to fit
• Protects against catching clothes

The Screw Eye bolt is ideally suited for fixing façade scaffolds, cables, or chains.

120mm depth, Overall 160mm long

Colour may vary

Can be used with Hook Ring Tie, see below

Fully Certified.

Rope Size: 20m length x 18mm diameter

These can be used in conjunction with ends bands or solely in order to help prevent the board from splitting. 

Colour / finish may vary.

Used to form temporary staircase, fully adjustable to any angle / rake and are left or right handed.

• Tread Size 1200 mm x 230 x 45mm
• 2 nos 100mm fixing tubes at each end
• Can be fitted with double couplers
• Colour / Finnish may vary.

Scaffold Boards to BS 2482. UK manufactured Kite Marked Boards, not cheaper imports. ( all timber is European Whitewood )

4ft / 1.2m length, 38mm thickness x 225mm width, fitted with end hoop irons for protection.

Available in the following lengths

• 13ft / 3.9m
  
• 10ft / 3.0m
  
•   8ft / 2.4m
  
•   6ft / 1.8m
  
•   5ft / 1.5m
  
•   4ft / 1.2m
•   3ft / 0.9m
•   2ft / 0.6m

Flame proof scaffold boards are also available on request.

If using Scaffold Boards for furniture etc... please contact the office on 01469 572321 prior to ordering.

Please be aware that scaffold boards are predominantly used outdoors, if used inside or in dry / hot weather conditions they will be subject to splitting etc, if using these for inside project / furniture etc they should be dry stored first to eliminate any cracking / splitting.

Scaffold Boards to BS 2482. UK manufactured Kite Marked Boards, not cheaper imports. ( all timber is European Whitewood )

3ft / 0.9m length, 38mm thickness x 225mm width, fitted with end hoop irons for protection.

Available in the following lengths

• 13ft / 3.9m
  
• 10ft / 3.0m
  
•   8ft / 2.4m
  
•   6ft / 1.8m
  
•   5ft / 1.5m
  
•   4ft / 1.2m
•   3ft / 0.9m
•   2ft / 0.6m

Flame proof scaffold boards are also available on request.

If using Scaffold Boards for furniture etc... please contact the office on 01469 572321 prior to ordering.

Please be aware that scaffold boards are predominantly used outdoors, if used inside or in dry / hot weather conditions they will be subject to splitting etc, if using these for inside project / furniture etc they should be dry stored first to eliminate any cracking / splitting.

Scaffold Boards to BS 2482. UK manufactured Kite Marked Boards, not cheaper imports. ( all timber is European Whitewood )

2ft / 0.6m length, 38mm thickness x 225mm width, fitted with end hoop irons for protection.

Available in the following lengths

• 13ft / 3.9m
  
• 10ft / 3.0m
  
•   8ft / 2.4m
  
•   6ft / 1.8m
  
•   5ft / 1.5m
  
•   4ft / 1.2m
•   3ft / 0.9m
•   2ft / 0.6m

Flame proof scaffold boards are also available on request.

If using Scaffold Boards for furniture etc... please contact the office on 01469 572321 prior to ordering.

Please be aware that scaffold boards are predominantly used outdoors, if used inside or in dry / hot weather conditions they will be subject to splitting etc, if using these for inside project / furniture etc they should be dry stored first to eliminate any cracking / splitting.

For use on tube, board & fitting scaffolds. After recognised construction industry feedback, we are now delighted to offer the Up & Over Loading Bay Gate for use with tube, boards and fittings.

• Double Handrail Depth
• Fully Meshed
• Tube, Board & Fitting  Compatible, with additional components.
• Gate Size: 3200 x 1000mm - size may vary.
  
• Please have gate available on site before erecting standards/posts
  
• Weight: 120 Kgs

Klawz is a new 'Double on Double' scaffold fitting that helps Scaffolders to reduce the amount of tube required and erect scaffolding faster than traditional methods.

The unique engineering of Klawz allows scaffolding schemes to be designed with high load bearing for both ledgers and transoms. The patented spacing means the ledger and transom sit together easily, allowing the scaffold to be boarded out on a single level whilst maximising strength, removing the need for supplementary structural transoms.

Klawz is fully tested in accordance with BS EN74-1:2005

Klawz exceeded Class B requirements in all tests, with a slip load of over 30 kN, more than double the requirement for a normal Class B fitting.

Screw Jacks locate in the bottom of the standards, they provide adjustment for variations in ground levels.

Overall Length: 315mm

Adjustable Range: 215mm

Safe working load of approx 4 tons each.

Approx 38mm OD.

Plate approx 150 x 150 x 5mm.

Screw Jacks locate in the bottom of the standards, they provide adjustment for variations in ground levels.

Overall Length: 205mm

Adjustable Range: 120mm

Safe working load of approx 4 tons each.

Approx 38mm OD.

Plate approx 150 x 150 x 5mm.

The Band features two 18mm bolt holes to allow the coupler to be fixed to a wall or ceiling etc.

Used in conjunction with the Screw Plate (Product Code: 40805) to form the Band & Plate set.

Zinc plated.

Colour / Finish may vary.

Please note, this is the Band ONLY.

Screw Plate used in conjunction with the Band (Product Code: 20805) to form the Band & Plate set.

Zinc plated.

Colour / Finish may vary.

Please note, this is the Plate ONLY.

353mm Ladder Beams,

Full spec sheet available on request. See technical data for more info.

Priced at £ 16.50 per foot / length

• 20ft Length
• 18ft Length
• 16ft Length
  
• 14ft Length
• 12ft Length
• 10ft Length
•   8ft Length
•   6ft Length
•   5ft Length
• Spigot Joints also available

The Screw Eye bolt is ideally suited for fixing façade scaffolds, cables, or chains.

230mm depth, Overall 160mm long

Please Note: Rawplugs are not supplied

Colour may vary

Can be used with Hook Ring Tie, see below

353mm Ladder Beams,

Full spec sheet available on request. See technical data for more info.

Priced at £ 16.50 per foot / length

• 20ft Length
• 18ft Length
• 16ft Length
  
• 14ft Length
• 12ft Length
• 10ft Length
•   8ft Length
•   6ft Length
•   5ft Length
• Spigot Joints also available

H.T. Galvanised Scaffold Tube

Drop Forged Half Coupler.Self Coupler

18mm Hole size approx.

Can be welded into place.

Colour / Finish may vary.