Fast Order: Scaffold Fittings

Pressed Steel Putlog Single Couplers connect scaffolding putlogs or transom scaffold tubes to ledger scaffold tubes for the support of scaffolding boards.

It should not be used as a load bearing scaffolding coupler. 

BS1139 Standard.

Colour / Finish may vary.

Double Couplers are used to connect ledgers to standards at 90 degrees.

EN74-1A / B Standard.

Colour / Finish may vary.

Double Couplers are used to connect ledgers to standards at 90 degrees.

EN74 Class B / 1B Standard.

Colour / Finish may vary.

Swivel Couplers enable two scaffold tubes to be connected together at any angle, they are used mainly for diagonal bracing.

EN74-1 Class A Standard.

Colour / Finish may vary.

Swivel Couplers enable two scaffold tubes to be connected together at any angle, they are used mainly for diagonal bracing.

EN74-1 Class A Standard.

Colour / Finish may vary.

Internal coupler for end to end joining of tubes, must only be used vertically and therefore sleeve couplers are now more commonly used for all joints.

Colour / Finish may vary.

Internal coupler for end to end joining of tubes, must only be used vertically and therefore sleeve couplers are now more commonly used for all joints.

Colour / Finish may vary.

External Coupler for end to end joints on either standards, ledgers or bracing.

EN74 Class B / 1B Standard.

Colour / Finish may vary.

Where secure connection of boards to scaffold is required.

Colour / Finish may vary.

Gravlock type girder clamps enable scaffold tubes to be secured to / against “I” beam girders.

Gravlocks should always be used in pairs.

AS-1576 Standard

Colour / Finish may vary.

Swivel Girder Clamps enable scaffold tubes to be secured to / against “I” beam girders.

Girder Clamps should always be used in pairs.

Fixed Type also available.

AS 1576 Standard.

Colour / Finish may vary.

Burton No 1 fitting is commonly known as the 'original' Girder Clamp.

Designed to be used in pairs and to secure to 'I' beams.

These are New, but may be 'Stock Rusty'

Colour / Finish may vary.

Approx max throat is 10/12mm

"The Jordan Safety Clamp" is a unique product devised to meet the need to eliminate the dangers faced by the scaffold operatives whilst working at height.

The Jordan Safety Clamp is a simple cost effective product that will save lives. Falls account for nearly two thirds of all fatal accidents in the construction industry. According to Health, Safety and Welfare Regulations 1996 operatives must be provided with SUITABLE means of protection to prevent a fall.

The primary safety objective is to provide physical safeguards to prevent falls during the erection, modification and dismantling of scaffolding installations. There is no equipment currently available to secure a man above head height at all times – The Jordan Clamp eliminates this problem.

The Jordan Safety Clamp, as inspected by the HSE, is a simple cost-effective safety device that enables the scaffolder to hook up to a failsafe security point as soon as he leaves ground level (or after all levels above the first lift). The scaffolder is secure at all times but has freedom of movement and can add or remove scaffolding components without unclipping his safety lanyard.

Before the introduction of The Jordan Safety Clamp scaffolders did not have a secure point of anchor when erecting dismantling or modifying scaffolding structures, these dangers are completely eliminated providing the scaffolder uses Jordan Safety Clamps.

The Jordan Safety Clamp is already secured to the standard as scaffold building begins from ground level, providing a safe anchor point above head height at all times. It allows instant access and continuous protection during all work and scaffolding operations and does not impede or slow down operations.

For use with standard tubes to convert them to putlogs.

Colour / Finish may vary.

Klawz is a new 'Double on Double' scaffold fitting that helps Scaffolders to reduce the amount of tube required and erect scaffolding faster than traditional methods.

The unique engineering of Klawz allows scaffolding schemes to be designed with high load bearing for both ledgers and transoms. The patented spacing means the ledger and transom sit together easily, allowing the scaffold to be boarded out on a single level whilst maximising strength, removing the need for supplementary structural transoms.

Klawz is fully tested in accordance with BS EN74-1:2005

Klawz exceeded Class B requirements in all tests, with a slip load of over 30 kN, more than double the requirement for a normal Class B fitting.

Used to provide a flat bearing surface for even load distribution of scaffold standards, should be used in conjunction with sole pads.

Colour / Finish may vary.

NOT Galvanised / plated

Heavy Duty Base Plate

Zinc Plated 150 x 150 x 4.0mm c/w locating spigot ( approx 30mm OD x 50mm )

Used to provide a flat bearing surface for even load distribution of scaffold standards, should be used in conjunction with sole pads.

Manufactured in accordance to EN74.

Colour / Finish : Self Colour

Six hole shear tie bracket with drop forged fitting
Use for applications where raking scaffolding away from structures is required
Use for punching tubes vertically or horizontally along a wall
For use in edge protection applications
Use in applications to support aluminium and steel beams
The rear of a scaffold tube will be 68 mm from the face of the structure.
In most applications use only two 12 mm fixing for a high load capacity into concrete, brick and blockwork.
Supplied in a zinc finish.

Dimensions:
Plate
AST8: 185x185x8 mm; Box section: 50x50x5 mm
Hole spacing’s
The corner holes are 150 mm apart horizontally and vertically.
The 2 no. 14 mm holes centrally positioned = 92.5 mm from the furthest edges
Fitting details
Drop forged fitting independently tested with minimum slip rating of 19 kN.
Slip rating of the drop forged fitting
The fitting complies with BS5973:1993 as a Class A fitting with a safe working slip load of 6.1 kN

Drop Forged Half Coupler.

18mm Hole size approx.

Can be welded into place.

Colour / Finish may vary.

Pressed Steel Half Coupler.

16mm Hole size approx.

Can be welded into place.

Colour / Finish may vary.

Used to hold down scaffold boards in exposed areas.

The advantages of using a Limpet Clip over standard board retaining clips are as follows:

• No trip hazard - domed finish.
• Fastened from above.
• No projecting bolts on underside.
  
• Can also be used on battens: 63mm thickness

Where secure connection of toe boards to standards is required.

Colour / Finish may vary.

Oyster Couplers connect putlogs or transom tubes to ledger tubes for the support of scaffold boards.

Oyster Couplers should not be used as a load bearing coupler.

BS1139 Standard.

Colour / Finish may vary.

Will secure timber joists to scaffold tube.

Fitting will take a timber 60mm width max.

Colour / Finish may vary.

 Was £2.65, Now Only £1.75 Each

Used to  secure hoarding / fence panels  to scaffold tube.

Will take a 45mm wide timber (max 47mm gap)

Colour / Finish may vary.

We also have available a joist coupler for use on timber joists / hoardings please

see Item No: 10907

Band & Plate coupler is used to connect two scaffold tubes at a right angle.

This two part coupler has two 18mm bolt holes to allow the coupler to be fixed to a wall or ceiling etc.

Zinc plated.

Colour / Finish may vary.

Components also sold seperately (Product Codes: 20805 & 40805)

The Band features two 18mm bolt holes to allow the coupler to be fixed to a wall or ceiling etc.

Used in conjunction with the Screw Plate (Product Code: 40805) to form the Band & Plate set.

Zinc plated.

Colour / Finish may vary.

Please note, this is the Band ONLY.

Screw Plate used in conjunction with the Band (Product Code: 20805) to form the Band & Plate set.

Zinc plated.

Colour / Finish may vary.

Please note, this is the Plate ONLY.

Used in pairs when a temporary stair tread is required, fully adjustable to any angle / rake and are left or right handed.

Complete stair tread units are also available.

Used to secure and safely fix a steel section ladder to a scaffold tube, use in pairs.

Double Sided for most section types.

Throat size: Approx 25mm width.

Colour / Finish may vary.

Used to secure and safely fix a timber pole ladder to a scaffold, use in pairs.

This Ladder Clamp should also be used to hold single section ladders against Kwikstage transom units.

Colour / Finish may vary.

Roofing Coupler used to hold Galv Corrugated Sheets in place.

Easy to use.

No drilling required.

May be Drop Forged or Pressed Steel depending on stocks

Roofing Coupler Fixing Sheet available to download.

Colour / Finish may vary.

The Lay Flat Scaffold Fitting eradicates the process of lapping boards on scaffold returns, reducing tripping hazards and increasing safety.

This Lay Flat Scaffold Fitting is tested to 9.1 KN with a Class B certification complete with EN74 – 1 BM

Colour / Finish may vary.

The Saddle Scaffold Fitting is for use with conventional Tube, Boards & Fittings.

 Colour / Finish may vary.

Was £4.50, Now Only £2.95 Each

Old Type Scaffold Tube to Fence Panel Coupler, used to secure two fence panels  to standard scaffold tube.

Tube can be horizontal or vertical.

Use combination spanner - V1 Old Type Anti-theft and  7/16" Spanner.

Requires Spike Type Spanner

Colour / Finish may vary.

Anti Theft Fence Panel Coupler, used to secure two fence panels together, the nut is of anti theft design and requires an anti theft spanner for use.

Please Note: This coupler requires a spike type spanner - Pt No 08551440 

Use special anti theft and 7/16" Spanner to fasten, these are available to purchase separately.

Colour / Finish may vary.

T Bolt, 7/16" Nut & Washer Set for Scaffold Fittings.

Come in packs of 100 pieces.

Fitting T Bolt - Weight 0.074kg, Length of Thread 53.5mm,  Overall Length 85mm 

Fitting Nut- Weight 0.022kg 

Fitting Washer - Weight 0.009kg 

All dimensions/weights are approximate.

Please note, this is a standard size for scaffold fittings, some scaffold fittings may require different size bolts.

Colour / Finish may vary.

SCAFFEZE quickly penetrates and removes rust, corrosion, grease and other contamination from all fittings and screw threads. SCAFFEZE not only frees all seized parts but also lubricates and leaves them in first class working order.

• Eco friendly
• Safe and reliable to use
  

Extendable Easi Fix Transoms provide a unique solution for the creation of
boarded platforms within traditional tube & fitting scaffolds.

Easi Fix Transoms can be used for most scaffolding equipment, Its purpose is to
provide a solid strength for the joints on the corners.

Easy fix transom needs only four bolts for secure placement of each unit and can be
used with flat base plates, avoiding any need for modifications or adjustments.

New Type Scaffold Tube to Fence Panel Coupler, used to secure two fence panels  to standard scaffold tube.

Tube can be horizontal or vertical.

Use combination spanner - V2 New Type Anti-theft and  7/16" Spanner.

Requires Socket Type Spanner NOT Spike Type Spanner

Colour / Finish may vary.

V2 Anti Theft Fence Panel Coupler, used to secure two fence panels together, the nut is of anti theft design and requires an anti theft spanner for use.

Please Note: This coupler requires a spike type spanner - Pt No 08551442

Use special anti theft socket and 7/16" Spanner to fasten, these are available to purchase separately.

Colour / Finish may vary.

Gravlok type anchor system

Please download pdf file for full info

Only to be used on good brick / solid walls / floors.

M16 Fitting

Gravlok type anchor system

Please download pdf file for full info

Only to be used on good brick / solid walls / floors.

M16 Fitting

Drop Forged Half Coupler.Self Coupler

18mm Hole size approx.

Can be welded into place.

Colour / Finish may vary.