Fast Order: New Cuplok

Standards are used for upright support.

They can be joined vertically to increase the scaffolds height.

Cups along thier length are used to connect Transoms and Ledgers, they are also used to hold Hop-Up Brackets.

SGB Code: 270300

Standards are used for upright support.

They can be joined vertically to increase the scaffolds height.

Cups along thier length are used to connect Transoms and Ledgers, they are also used to hold Hop-Up Brackets.  

SGB Code: 270200

Standards are used for upright support.

They can be joined vertically to increase the scaffolds height.

Cups along thier length are used to connect Transoms and Ledgers, they are also used to hold Hop-Up Brackets.

SGB Code: 270100

Ledgers are used to tie the uprights/standards along the length of the scaffold.

They are also used to form the guard rail.

Ledgers have a blade fixing that is located into the cup on the standards.

SGB Code: 271250

Ledgers are used to tie the uprights/standards along the length of the scaffold.

They are also used to form the guard rail.

Ledgers have a blade fixing that is located into the cup on the standards.

SGB Code: 271180 

Ledgers are used to tie the uprights/standards along the length of the scaffold.

They are also used to form the guard rail.

Ledgers have a blade fixing that is located into the cup on the standards.  

SGB Code: 271130

Ledgers are used to tie the uprights/standards along the length of the scaffold.

They are also used to form the guard rail.

Ledgers have a blade fixing that is located into the cup on the standards.

Ledgers are used to tie the uprights/standards along the length of the scaffold.

They are also used to form the guard rail.

Ledgers have a blade fixing that is located into the cup on the standards.

Ledgers are used to tie the uprights/standards along the length of the scaffold.

They are also used to form the guard rail.

Ledgers have a blade fixing that is located into the cup on the standards.

Used in the same way as a 2.5m Ledger/Transom but to carry Battens and not Boards.

Omega is the term given to any component that is designed to be used with Battens.

Used in the same way as a 1.8m Ledger/Transom but to carry Battens and not Boards.

Omega is the term given to any component that is designed to be used with Battens.

Used in the same way as a 1.3m Ledger/Transom but to carry Battens and not Boards.

Omega is the term given to any component that is designed to be used with Battens.

Used in the same way as a 0.9m Ledger/Transom but to carry Battens and not Boards.

Omega is the term given to any component that is designed to be used with Battens.

Used in the same way as a 0.8m Ledger/Transom but to carry Battens and not Boards.

Omega is the term given to any component that is designed to be used with Battens.

Used in the same way as a 0.6m Ledger/Transom but to carry Battens and not Boards.

Omega is the term given to any component that is designed to be used with Battens.

Used to join scaffolds at 90 degrees.

Omega is the term given to any component that is designed to be used with Battens.

A Return Device is used where a further scaffold run is required at 90 degrees to the main scaffold.

They are connected to a standard by the cup fastening and simply hook over the ledger on the next run.

Intermediate transoms are used to support the scaffold boards at 1.2m centers.

They can be placed anywhere on a scaffold run and are located across the ledgers.

Intermediate transoms are used to support the scaffold boards at 1.2m centers.

They can be placed anywhere on a scaffold run and are located across the ledgers.

Used as an Intermediate transoms, these support the scaffold boards at 1.2m centers and also allow an extra board to be placed between the scaffold and the building.

Other sizes are available on request.

Used as an Intermediate transoms, these support the scaffold boards at 1.2m centers and also allow an extra 2 boards to be placed between the scaffold and the building.

Other sizes are available on request.

Used as an Intermediate transoms, these support the scaffold boards at 1.2m centers and also allow an extra 3 boards to be placed between the scaffold and the building.

Other sizes are available on request.

A Swivel Face Brace is used on the elevation or face of the scaffold to "lock" the Standards and Ledgers into a rigid bay.

They also remove any "sway" in the scaffold.

For house building it is good practice to have one brace on every fourth bay and zig-zag up the face of the scaffold.

A Swivel Face Brace is used on the elevation or face of the scaffold to "lock" the Standards and Ledgers into a rigid bay.

They also remove any "sway" in the scaffold.

For house building it is good practice to have one brace on every fourth bay and zig-zag up the face of the scaffold.

A Swivel Face Brace is used on the elevation or face of the scaffold to "lock" the Standards and Ledgers into a rigid bay.

They also remove any "sway" in the scaffold.

For house building it is good practice to have one brace on every fourth bay and zig-zag up the face of the scaffold.

A Swivel Face Brace is used on the elevation or face of the scaffold to "lock" the Standards and Ledgers into a rigid bay.

They also remove any "sway" in the scaffold.

For house building it is good practice to have one brace on every fourth bay and zig-zag up the face of the scaffold.

Omega Hop-Up Brackets enable work to take place away from the main scaffold run.

They are available in 1,2 and 3 board widths.

Hop-Up Brackets are also very usefull if the building is to be rendered as they can be in place on construction but removed for the rendering giving the workers easy access.

2 Board and 3 Board Hop-Up Brackets should be tied together using standard ledgers of the same bay size .

Hop-Up Brackets enable work to take place away from the main scaffold run.

They are available in 1,2 and 3 board widths.

Hop-Up Brackets are also very usefull if the building is to be rendered as they can be in place on construction but removed for the rendering giving the workers easy access.

2 Board and 3 Board Hop-Up Brackets should be tied together using standard ledgers of the same bay size .

Hop-Up Brackets enable work to take place away from the main scaffold run.

They are available in 1,2 and 3 board widths.

Hop-Up Brackets are also very usefull if the building is to be rendered as they can be in place on construction but removed for the rendering giving the workers easy access.

2 Board and 3 Board Hop-Up Brackets should be tied together using standard ledgers of the same bay size .

Hop-Up Brackets enable work to take place away from the main scaffold run.

They are available in 1,2 and 3 board widths.

Hop-Up Brackets are also very usefull if the building is to be rendered as they can be in place on construction but removed for the rendering giving the workers easy access.

2 Board and 3 Board Hop-Up Brackets should be tied together using standard ledgers of the same bay size .

0.795m Ledgers are used to tie the uprights/standards to Handrail Posts fitted to hop-up brackets, used in pairs to form a double handrail. 

These ledgers are for use on 3 Board Hop-Up Brackets ONLY - with either timber boards or Omega battens.

Ledgers have a blade fixing that is located into the cup on the standards.

Use in pairs - sold individually

Timber Battens fit between the Omega Transoms to give a solid working platform.

They are also used on Omega Hop-Up Brackets.

UK manufactured from mixed Eurpoean Whitewood to BS2482.

Approx dimensions - 2450mm x 225mm x 63mm

Available in 2.5m, 1.8m & 1.3m lengths.

Timber Battens fit between the Omega Transoms to give a solid working platform.

They are also used on Omega Hop-Up Brackets.

UK manufactured from mixed Eurpoean Whitewood to BS2482.

Approx dimensions - 1750mm x 225mm x 63mm

Available in 2.5m, 1.8m & 1.3m lengths.

UK manufactured from mixed Eurpoean Whitewood to BS2482.

Approx dimensions - 1250mm x 225mm x 63mm

Available in 8ft, 6ft & 4ft lengths.

Compatible with both Kwikstage and Cuplok.

Metal end plate for use on Scaflok/Cuplok battens.

Galvanised Steel Battens BS EN12811-1

Used where timber battens are not suitable, more expensive than timber but last longer.

Please note that we supply steelstage to SGB Cuplok spec,some other

suppliers sell 225/230 x 63mm steelstage so please check your stock.

Tech sheet available on downloads button.

Size:  238mm width,  57mm depth/thickness

Available in 2.5m, 1.8m & 1.3m lengths. 

Galvanised Steel Battens BS EN12811-1

Used where timber battens are not suitable, more expensive than timber but last longer.

Please note that we supply steelstage to SGB Cuplok spec,some other

suppliers sell 225/230 x 63mm steelstage so please check your stock.

Tech sheet available on downloads button.

Size:  238mm width,  57mm depth/thickness

Available in 2.5m, 1.8m & 1.3m lengths. 

Screw Jacks locate in the bottom of the standards, they provide adjustment for variations in ground levels.

Safe working load of approx 4 tons each.

Overall Height approx 650mm, Adjustable Range approx 500mm

Approx 38mm OD.

Plate approx 150 x 150 x 5mm.

Screw Jacks locate in the bottom of the standards, they provide adjustment for variations in ground levels.

Safe working load of approx 6 tons each.

Overall Height approx 650mm, Adjustable Range approx 500mm

Approx 38mm OD

Plate approx 150 x 150 x 6mm.

Screw Jacks locate in the bottom of the standards, they provide adjustment for variations in ground levels.

Overall Length: 315mm

Adjustable Range: 215mm

Safe working load of approx 4 tons each.

Approx 38mm OD.

Plate approx 150 x 150 x 5mm.

Screw Jacks locate in the bottom of the standards, they provide adjustment for variations in ground levels.

Overall Length: 205mm

Adjustable Range: 120mm

Safe working load of approx 4 tons each.

Approx 38mm OD.

Plate approx 150 x 150 x 5mm.

Heavy Duty Base Plate

Zinc Plated 150 x 150 x 4.0mm c/w locating spigot ( approx 30mm OD x 50mm )

Used to provide a flat bearing surface for even load distribution of scaffold standards, should be used in conjunction with sole pads.

Manufactured in accordance to EN74.

Colour / Finish : Self Colour

For use with Base Plates or Base Jacks on soft ground conditions.

Approx 18" length.

Tube Castor for fitting onto a Cuplok standard

Will also fit scaffold tube and/or Kwikstage and some other system scaffold standards.

• Braked
• Rubber Tyre
• 8" - 200mm
  
• SWL Approx 535kgs

Used in pairs to bridge over doorways etc.

Handrail Posts must be used with the Bridging Ledger.

Care should be taken for any erection on top of the bridging ledgers.

The bridging ledger should not be used to form a load bearing structure, if you require to be able to build above the bridge then beams should be used instead.

To be used with a 5.0m bridging ledger to form a handrail.

Can also be used on 2 and 3 Board Hop-Up Brackets.

To create a working platform above the standard.

Up and Over Loading Bay Gate - Zinc Plated

Used on a loading bay within a 2.5m x 2.5m tower.

You will require the following items to build a loading bay...

• 2 nos Loading Bay Transoms
• 8 nos Loading Bay Omega Supports
• 10 nos Steelstage
• 2 nos 8ft Scaffold Tubes
• 1 nos Up & Over Gate

Can be used on Boards or Omega Batten Loading Bay. 

Use to form a 2.5m x 2.5m loading bay.

You will also require loading bay transom intermediate supports

These Loading Bay Transoms can be used for either Omega system or scaffold boards, other items will be required.

Loadings: 6 kN/m2 = 3.8 tonne UDL over the platform area.

Use to form a 2.5m x 2.5m loading bay.

You will also require loading bay transoms.

These Loading Bay Supports are for Omega system.

8nos required per 2.5m tower/lift.

Box section size approx 90 x 50mm.

Use to form a 2.5m x 2.5m loading bay.

You will also require loading bay transoms.

These Loading Bay Supports are for board system.

8nos required per 2.5m deck/lift.

Box section size 80 x 35mm.

Omega ladder access transoms are used to support the Omega Battens, whilst leaving a ladder access opening.

They can be placed anywhere on a scaffold run and are located across the ledgers.

Intermediate ladder access transoms are used to support the scaffold boards, whilst leaving a ladder access opening.

They can be placed anywhere on a scaffold run and are located across the ledgers.

Used as a safety trap door, a ladder access transom is used on the scaffold to form a " hole / opening " that a worker can climb through. The safety trapdoor is held in place by adjustable clamps held against the toeboards.

• Fits on Kwikstage
• Fits on Scaflok / Cuplok
• A ladder access transom will also be required.
• Fitting details available on the download
  
• Colour may vary
• Mesh size: 58 x 71cm (may vary)
  

Design may vary.

Swan Neck Standards are used for upright support when an Access Safety Gate is required.

They are connected to two ledgers and then form an intermediate standard for two shorter ledgers to form a double handrail.

New Ladder Access Kit

Used where a ladder access c/w safety gate is required in a 2.5m Cuplok bay.

The standard 2 nos 2.5m ledger handrails are replaced with 2 nos 1.8m ledgers, one of the 2.5m ledgers being used to locate the swan neck standard on the lugs on the lift below the deck height.

Kit comprises:

2 nos 1.8m Ledgers

1 nos Swan Neck Standard

1 nos Access Safety Gate

The existing 2.5m ledgers are reused, the toe board will require cutting and refitting (not shown in photo)

You will also require a tube/bracket to secure the ladder at 90 degrees to the scaffold.

New Ladder Access Kit

Used where a ladder access c/w safety gate is required in a 1.8m Cuplok bay.

The standard 2 nos 1.8m ledger handrails are replaced with 2 nos 1.3m ledgers, one of the 1.8m ledgers being used to locate the swan neck standard on the lugs on the lift below the deck height.

Kit comprises:

2 nos 1.3m Ledgers

1 nos Swan Neck Standard

1 nos Access Safety Gate

The existing 1.8m ledgers are reused, the toe board will require cutting and refitting (not shown in photo)

You will also require a tube/bracket to secure the ladder at 90 degrees to the scaffold.

New Ladder Access Kit

Used where ladder access c/w safety gate is required in a 1.3m Cuplok bay.

For use with Intermediate Transoms/Boards

The standard 2 nos 1.3m ledger handrails are replaced with 2 nos 0.6m ledgers, one of the 1.3m ledgers being used to locate the swan neck standard on the lugs on the lift below the deck height.

Kit comprises:

2 nos 0.6m Ledgers

1 nos Swan Neck Standard

1 nos Access Safety Gate

The existing 1.3m ledgers are reused, the toe board will require cutting and refitting (not shown in photo)

The above only applies to Cuplok Scaffold where Intermediate Transoms are being used.

For use with Omega Transoms/Battens

If you require access to the end of a bay and are using Omega battens you will need to cut a slot in the outside lip of the Omega Transom to accomodate the tube from the Swan Neck Standard, Please Note that if you cut the tray on the Omega Transom it should NOT be used for any other application.

In both cases you will also require a tube/bracket to secure the ladder at 90 degrees to the scaffold.

The Cuplok staircase is used for access to different deck levels within a scaffold.

The staircase unit fits between the ledger on the bottom lift and the ledger on the upper lift.

The staircase units DO NOT fit onto the Omega system transoms.

Handrails are obtained using standard swivel face braces, an additional handrail support can be added to form a return handrail where needed.

The size of staircase unit is measured by the bay width x lift height

ie: 1.8 x 2.0m

These units can be fitted into a 2.5m width bay but you will need to add an intermediate transom at the bottom and then continue to board out the deck.

There is also a metal grating grid available for a 1.8m wide bay, this enables you to have a riser and lower staircase on the same landing.

The need for a handrail post depends on where your standards are on the bay/size of bay. See side photos.

The Cuplok staircase is used for access to different deck levels within a scaffold.

The staircase unit fits between the ledger on the bottom lift and the ledger on the upper lift.

The staircase units DO NOT fit onto the Omega system transoms.

Handrails are obtained using standard swivel face braces, an additional handrail support can be added to form a return handrail where needed.

The size of staircase unit is measured by the bay width x lift height

ie: 1.8 x 1.5m

These units can be fitted into a 2.5m width bay but you will need to add an intermediate transom at the bottom and then continue to board out the deck.

There is also a metal grating grid available for a 1.8m wide bay, this enables you to have a riser and lower staircase on the same landing.

The need for a handrail post depends on where your standards are on the bay/size of bay. See side photos.

Used to form a handrail post where no standard socket/joint is available.

Mainly used with staircase units to form a return handrail.

A complete landing platform for use on 4-leg staircase towers.

Slots over horizontals and provides support for the staircase unit and guardrail posts

After recognised construction industry feedback, we are now delighted to offer the LH / RH side panel to enable a standard self closing gate to be used on the end of a Cuplok bay ie 1.3m width.. or a kwikstage bay ie 4'2 width.

• Double Handrail Depth
• Painted Finish
• Can be used RH or LH Side
• Steel Toe Board
• Fully Meshed
• Works with standard and omega cuplok system
• Works with kwikstage
• System Compatible, with additional components.
• Used with Gate Size: 750 x 960mm( not included )
  
• Weight: 10 Kgs

Pigs Tail Joint Pins for use with Kwikstage or Cuplok.

Supplied individually

These are a "loose" fit item, not to be used for suspended scaffolds.

Scaffold Stillage to hold either standard scaffolding and/or Kwikstage or Cuplok items.

Designed to stack together, will fit on top of fitting bins.

• Standard Size
• Fits on/under Fitting Bins
• Robust Construction
• Square Leg
• SWL 1.4 tons
• Can stack 6 high

CONDITION MAY VARY

Scaffold Stillage to hold either standard scaffolding and/or Kwikstage or Cuplok items.

Designed to stack together, will fit on top of fitting bins.

• Standard Size
• Fits on/under Fitting Bins
• Robust Construction
• Square Leg
• SWL 1.4 tons
• Can stack 6 high

Painted Black

Scaffold Bin to hold scaffold fittings and/or Kwikstage or Cuplok items.

Designed to stack together, will fit on top of stillages or fitting bins.

• 940cm x 940cm. 645cm Overall Height, 380cm Internal Height
• Fits on/under Fitting Bins or Stillages
• Robust Construction
• SWL 1.0 ton
• Can stack 6 high
• Please note that these bins are once used.
  

New 2.5m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 5.0m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 7.5m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 10.0m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available - Ask for details

New 12.5m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 15.0m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 17.5m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 20.0m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New addittional bay, 2.5m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 2.5m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 5.0m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 7.5m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 10.0m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 12.5m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 15.0m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 17.5m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

New 20.0m x 4.5m platform height, Cuplok scaffolding c/w double handrails, toeboards, braces etc.

• Easy to erect Cuplok System.
• Easily expanded to any size.
• Options available New Timber or Galv Steel Deck

Training Course available, see link below:

Access Training

Twin Stabiliser Kit - for use on Kwikstage or Cuplok Runs.

Each kit contains two full stabilisers:

• P.S. Swivel Couplers - 4 nos
• P.S. Double Couplers - 4 nos
• Sleeve Couplers - 2 nos
• 10ft Galvanised Tube - 4 nos
•  8ft Galvanised Tube - 2 nos
  

To be used where extra stability is required or where wall ties can not be used.

We recommend that you use a minimum of 2 Stabilisers every four bays.

Where platform height is above 4.5m then extra ties or tubes will be required.

Galvanised Spigots for Standards/uprights.

Used as a replacement for damaged/missing spigots in standards.

Compatible with both Cuplok & Kwikstage.

Complete with one nut & bolt.

After recognised construction industry feedback, we are now delighted to offer the LH / RH closing gate.

• Double Handrail Depth
• Steel Toe Board
• Fully Meshed
• System Compatible, with additional components.
• Gate Size: 600 x 960mm - size may vary.
• Distance between standards: 780mm Approx
• Please have gate available on site before erecting standards/posts
• Presco type half coupler fastening
• Weight: 12 Kgs